Interplater hd85 thermal pdf. Thermal analysis and design enae d principles of space systems design u n i v e r s i t y o f maryland nonideal radiative. Service Manual + 68/85 Plate Processor InterPlater 85/ HD Polymer Service manual Plate Processor+ 68/85 .. Cleaning of developer heating element. Thermal Plate Processor Raptor 85/ Interplater HD 85 G&J used/refurbished. Glunz Jensen Interplater Plate Processor Model Perfect Condition.

Author: Dukinos Meztigar
Country: Comoros
Language: English (Spanish)
Genre: Spiritual
Published (Last): 17 November 2004
Pages: 240
PDF File Size: 6.1 Mb
ePub File Size: 6.72 Mb
ISBN: 183-2-74571-323-7
Downloads: 59280
Price: Free* [*Free Regsitration Required]
Uploader: Bataxe

Normally no adjustments are necessary. When cleaning the tank, make sure to wash off all residues around the developer heating element. Tighten with the filter key 3.

Lead the cable as shown below. Spare parts and service period: Connect conductors in power cord to terminals: For cleaning of rollers, guides, tank walls, and all surfaces, especially the exit table and the feed table if fitted.

The fuses are placed on the fuse PCB interplaater the cover. The stop-roller 15 on top of the entrance rollers 16 prevents that the wash water runs back into the developer section, and water is squeezed off the plate by the section exit rollers Make sure that innterplater obtain a uniform grip in both sides and in the middle. For cleaning the inside and the holes of the spray tubes.

Products | Glunz & Jensen

Rollers with dents or other marks must be changed. The installation procedure is described later in this manual. Level out 1355 processor lengthwise by placing a spirit level on the left 4 and right 5 tank side. The water solenoid valve will let in water when a plate is entered through the input slot.


See power outlet and fusing requirements later in this manual.

Solar thermal energy an industry report solar thermal technology on an industrial scale the sun is our source our sun produces ,,,, watts of energy every thernal and the belief is that it will last for another 5 billion years. Level out the processor by placing the spirit level inside the preheat 7or between the preheat and the prewash tank.

How to read pdf files in my mobile

When mounting upper roller insert the roller key between the upper roller and the lower roller as shown 3.

Processor must turn off when set to “0”. Make sure covers are secured by screws. Installation of setter interface See the setter interface manual. This manual is published by: Before operating the processor you may need to perform a rewiring to match your local supply voltage. Lift the exit table to vertical position 1. If the machine has low level thedmal starting up, or goes low level during production, the pump will start automatically filling up to level.

InterPlater 85/135 HD Service Manual

If main power has been cut off temporarily the processor switches to off mode green led flashes. Contact your local supplier for information about storage requirements for plates and chemicals. Touch screen control panel MMI A graphical user interface colour display.

Therjal for additional cable protection, e. The processor is Class 1 equipment.

Notation M8 is used on Rapzac processors. The operator may step onto cable. See illustration on the following page.

Lead the supports through the holes in the rear panel 3b and secure them inside using the enclosed locking split pins 3c.

The parameters to be configured are: Removing the fenders and stand panels In order to make the installation it will be necessary to remove covers, lids, left fender, and the stand interplated from the processor: A-8 Sensors and control devices. Operating and cleaning procedures in cartoon version. Adjustment – method B Use a strip of film and a spring balance and proceed as follows: Mount red, yellow and brown wire in terminal 1.


Introduction about this manual general this manual covers the spare parts for the platewritertm system. The gum solution from the application tube 20 forms a small bath between these two rollers and a thin layer of finisher is applied to the plate while the extra finisher is forced backwards. When performing any service, maintenance, calibration, or trouble shooting etc. The directions given must not be followed by unauthorized personnel. It is necessary htermal control the level at the preheat also and adjust if necessary Check leveling in all 4 positions and make final leveling interlater required.

The exit roller pair 21 takes the plate when dry and leads it inteerplater of the processor. F17 Transport motor M1 4AT, 6. Also the developer top-up function automatically adds fresh developer to the developer section when low level is detected. When installation of the setter interface is complete knterplater return to this manual for finishing the entire installation by continueing with the instructions on the next page.

Low Voltage Wiring Title: