E5EK OMRON PDF

This User’s Manual describes how to use the E5EK compact, high-function digital Nevertheless, OMRON assumes no responsibility for errors or omissions. E5EK-AA Omron Automation and Safety Controllers 1/8 DIN VAC Digital field config datasheet, inventory, & pricing. This product was manufactured at OMRON Okayama. OMRON Okayama has obtained approvals from international certification bodies for its quality system and.

Author: Shakatilar Mikree
Country: Congo
Language: English (Spanish)
Genre: Environment
Published (Last): 1 June 2013
Pages: 34
PDF File Size: 2.32 Mb
ePub File Size: 11.97 Mb
ISBN: 514-9-95465-853-9
Downloads: 17970
Price: Free* [*Free Regsitration Required]
Uploader: Fenrijinn

Setting Up 2 Draw out the internal mechanism towards you holding both sides of the front panel. Read this chapter while referring to the parameter descriptions in chapter 5. During operation of the ST function, e5e power on the load side connected to the control output must be turned ON at the same time or before start of E5EK Function operation.

Omron E5EK-AA Processor/Controller | eBay

When the manipulated variable calculated by the E5EK controller is outside of the upper-and lower-limit range, the upper e5rk Function or lower limit set to these parameters is output, respectively. Input And Output SP input.

The process Calibration item How- ever, note that terminal Nos. Set the STV output to 5V. These abbreviations mean the following. If the key is pressed for less than one second, the parameters are switched. Also, when the input type, temperature unit and scaling sensor range are changed, set point limiter is forcibly reset to the scaling sensor range.

The display changes to [ ] 5 V calibration display. However, be sure to execute motor calibra- tion after connecting the potentiometer. Failure to heed precautions can result in inju- ry to people or damage to the product.

Got it, continue to print. In this mode, you can pmron the communications conditions, transfer output and event input parameters to match the type of option unit set in the controller. Page The display changes to [ ] 5 V calibration display.

  DOUGLAS HOFSTADTER - I AM A STRANGE LOOP PDF

Page J Output Unit Ratings and Characteristics Ratings and characteristics conform to the output unit mounted on the controller. In other words, you cannot switch between the auto and manual operations by key operation. Page The setting range varies according to this output data. Page setup mode can be used. Operating Condition Restrictions The upper limit is set for the heating side positive valueand the lower limit is set for the cooling side negative value as shown in the follow- ing figure.

About The Communications Function 1. Undefined Error Check the communications condition. To print the manual completely, please, download it. The following figures shows the effect on data after passing through the digital filter. Al- ways heed the information provided with them. Memory error F Meaning Internal memory operation is in error. However, note that s5ek thermocouple R, S, E, B, W or PLII is used, the cold junction compensator and the compensating conductor can be substi- tuted with the cold junction compensator and the compensating con- f5ek for thermocouple K.

Enter text from picture: Set the STV output to 0 mA.

OMRON E5EK User Manual

Use this end code to remedy errors that may occur. Don’t have an account? For details on the communications function, refer to Chapter 6. Alarms 1 to 3, 5: The following conventions are used to indicate and classify precautions in this manual.

Page 84 PID control, standard con- trol or heating and cooling control. Page The following figure shows the required device connection.

The upper limit is set for the heating side positive valueand the lower limit is set for e5ei cooling side negative value as shown in the follow- ing figure. Setting Up The Output Unit 2. Manual Operation F Dead band The dead band is set with the set point as its center. F Meaning Calibration data is in error. You can select this mode only when the option unit is set in the controller. D Setting up the E5EK Pay Attention to the Following when Installing this Controller F If you remove the controller from its case, never touch nor apply shock to the elec- tronic parts inside.

  CARPROG AIRBAG PDF

APPENDIX F Startup Conditions of DT 1 DT will start if the temperature that has been stable varies due to external disturbance and the e5wk of the temperature exceeds the stable range, and then the temperature becomes stable, pro- vided that the number of maximum temperature values is less than four.

F Option mode This is the mode for setting option functions.

Chapters Table Of Contents Omro Unit Default Setting Range SP The output ranges of the SP setting, set point or process value when temperature input is selected are the ranges sup- ported by the selected sensor. Dead band Hysteresis heat Page The functions of this omrpn change according to how long it is pressed. Revision History A manual revision code appears as a suffix to the catalog number on the front cover of e5e, manual. Control output cool2: No part of this publication may be reproduced, stored in a retrieval system, or trans- mitted, in any form, or by any means, mechanical, electronic, photocopying, recording, recording, or other- wise, without the prior written permission of OMRON.

If you select the desired mode using the The following figure shows the required device connection.