ASTM B – Designation: B /B M – 01 Standard Speci?cation for Copper -Nickel-Tin Alloy, C. This standard is issued under the fixed designation B /B M; the number . ASTM designation and year of issue (B/. B M. ASTM B attains the requirements for copper-nickel alloy plates, sheets, strips, and rolled bars made from UNS C, UNS C alloy. Such Sheet or.
|Published (Last):||19 July 2013|
|PDF File Size:||15.27 Mb|
|ePub File Size:||7.99 Mb|
|Price:||Free* [*Free Regsitration Required]|
Required properties for other tempers shall be agreed upon between manufacturer and purchaser at the time of placing the order.
Within the text, SI units are shown in brackets. There are two main production streams that is used to produce rolled bar products.
Cupro Nickel (UNS C, ASTM B)
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
B Scale 68—82 80—90 87—94 89—96 Super? Grain Size for Annealed Tempers 9. NOTE 3—The Rockwell hardness test offers a quick and convenient method of checking for asym conformity to the speci?
70-30 Cupro Nickel
C are required, see appropriate table. C 4 55 18 Blooms are used for rolling structural products such as I-sections, channels, rail etc. Limits may be established for unnamed elements by agreement between manufacturer or supplier and purchaser.
C Rockwell hardness values apply as follows: When all elements in Table 1 are analyzed, their sum shall be b22 follows: The values stated in each system are not exact equivalents; therefore, each system shall 1 This speci?
A billet is rolled out of bloom, has at least asgm mm X 40 mm cross-section. Workmanship, Finish and Appearance The B and G scale hardness values apply to metal 0. Billets are rolled into bars, rods. The ingot is soaked at the hot astk temperature and then rolled into blooms or billets or slabs. In case of disagreements, the chemical composition is determined following appropriate methods listed here.
The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. When all the elements in Table 1 are analyzed, their sum shall be as follows: Although no minimum grain size is required, this material shall be fully recrystallized.
D Standard designation de? This adtm is subject to revision at any time by the responsible technical committee and must be reviewed every?
C and C M20 H01 H02 H04 H06 H08 as hot-rolled quarter hard half hard hard extra hard spring 45 58 66 75 80 84     ashm  65 72 80 88 92 94       Siddhagiri Metals and Tubes Manufacturer: Current edition approved May 10, Each product should be manufactured by hot or cold working, and annealed if required, to produce a uniform wrought b1222 that meets the specified temper properties.
Looking for some more information? C and C to this standard in and Tables Copper plus elements with speci?
A number in parentheses indicates the year of last reapproval. Within the text, the SI units are shown in brackets. The following alloys are covered:. C M20 H01 H02 H04 H06 H08 A B as hot-rolled quarter hard half hard hard extra hard spring 60  69  78  92    80  87  95     C 6 80 The second is the electric arc furnace EAFwhich primarily uses steel scrap as the raw material. This specification also contains information on the standard tempers for and tensile strengths of hot-rolled, cold-rolled, and annealed tempers.
C M20 H01 as hot-rolled quarter hard 52  58  65  72  C 9 70 10 Originally published as B — 39 T.
C M20 H01 H02 H04 H06 H08 as hot-rolled quarter hard half hard hard extra hard spring 38 47 56 67 72 76       56 63 70 79 84 87     b122  This standard has been approved for use by agencies of the Department of Defense.
Siddhagiri Metals and Tubes Rating: Mechanical Property Requirements Grain size is the standard requirement for all products in the annealed tempers. Offer on Fasteners Sitemap. Dimensions, Mass, and Permissible Variations C Phosphorus at 0.
ASTM B Copper Nickel Sheet Plate Supplier · B C/C
C 3 65 10 Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
ASTM does not give atsm warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Combining values from the two systems may result in nonconformance with the speci?
It is informational only and not an official part of the standard; the full asttm of the standard itself must be referred to for its use and application. C 8 59 12