ASTM A – Designation: A /A M – 01 An American National Standard Standard Practice f. This standard is issued under the constant designation a /a m; the number right away following the designation suggests the yr. according to the guidelines of ASTM E, “Standard Guide for ASTM A, “Standard Practice for Steel Casting, Austenitic Alloy.
|Genre:||Health and Food|
|Published (Last):||15 August 2011|
|PDF File Size:||18.50 Mb|
|ePub File Size:||6.74 Mb|
|Price:||Free* [*Free Regsitration Required]|
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. A superscript epsilon e indicates an editorial change since the last revision or reapproval. The Eng-Tips staff will check this out and take appropriate action. S800 number in parentheses indicates the year of last reapproval.
ASTM , Ferrite content (CF8M) – Metal and Metallurgy engineering – Eng-Tips
Digital Transformation may be defined in a number satm different ways by analysts or enterprise software vendors. All measurements shall be made on weld deposits as deposited.
Thank you for helping keep Eng-Tips Forums free from inappropriate posts. These may so alter the magnetic response of the alloy that the indicated ferrite content is quite different from that of the same chemical composition that has undergone different thermal treatment. Also, because the magnets or probes of the various measuring instruments are small, different degrees of surface roughness or surface curvature will vary the magnetic linkage with the material being measured.
The ferrite content may be limited by purchase order requirements or by the design construction codes governing the equipment in which the castings will be used. If a comparison is made of ferrite content estimated from a product analysis awtm by the purchaser, with that estimated from the heat analysis see 7. Signicance and Use 4. Click Here to join Eng-Tips and talk with other members!
Historical Version s asym view previous versions of standard. Register now while it’s still free! Thanks for any help RE: Because of segregation, the chemical composition, and, therefore, the ferrite content, may differ from point to point on a casting.
The estimates of ferrite content from magnetic measurements S1 or from point counts S2or both, if ordered by the purchaser, also shall be reported. The gures immediately above and below on the lines U and L indicate the probable upper and lower bounds of the ferrite range that may be expected.
Thanks for any help. BoxN. ASTM D e1.
Current edition approved Mar. Similar information is available in Table X1.
Standard Practice for Steel Casting, Austenitic Alloy, Estimating Ferrite Content Thereof
Determination of the ferrite content by any of the procedures described in the following practice is subject to varying degrees of qstm which must be recognized in setting realistic limits on the range of ferrite content specied. Measurements may be made either before or after performance of the tension test.
Sources of error include the following:. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Combining values from the two systems may result in nonconformance with the practice. The possible extent of this difference is shown by the broken lines.
Within the text, the SI units are shown in brackets. Defense manufacturing is all about project manufacturing and project accounting. The values ast, in each system are not exact equivalents; aetm, each system must be used independently of the other.
Aastm the composition ratio is 1. They shall not apply unless specied in the order, in which event the specied methods of ferrite content estimation shall be employed by the manufacturer before shipment of the castings.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Because of errors in chemical analyses, the calculated ratio may differ from the actual composition ratio and, as a result, the ferrite content may be higher or lower than indicated by the central X1.
Link to Active This link will always route to the current Active version of the standard. Promoting, selling, recruiting, coursework and thesis posting is forbidden.
Download Now White Paper: By joining you are opting in to receive e-mail. The quantity of ferrite in the structure is fundamentally a function of the chemical composition of the alloy and its thermal history. These may so alter the magnetic response of the alloy that the indicated ferrite content is quite different from that of the same chemical composition that has undergone different thermal treatment. Originally published as A — This may be formed upon solidication from the molten metal delta ferrite or by transformation from austenite or sigma phase on cooling in the solid state alpha ferrite.
Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Determination of the ferrite content by any of the procedures described in the following practice is subject to varying degrees of imprecision which must be recognized in setting realistic limits on the range of aastm content specified.
Accordingly, if additional estimates of ferrite content are adtm by magnetic or metallographic methods, they can be expected to a800 from the diagram value. Close this window and log in. When measurements are made on a curved surface the radius of curvature must be greater than 0. Resources Digital Transformation may be astj in a number of different ways by analysts or enterprise software vendors.