ASTM A311 PDF

(Identical to ASTM Specification A /A M (R) except for deletion of , revision of Table 1 footnote A, and editorial corrections to Table 2.) 1. A Class B Stressproof TG&P Cold Finished Bar Round Turned Ground Polished, A Round Bar, A Rod, A TG&P Rod, A TG&P Round Rod . See the chemical composition and physical properties of ASTM A Grade cold-drawn, stress relieved, annealed bar, find alternative materials, and.

Author: Takinos Kazishicage
Country: Mauritius
Language: English (Spanish)
Genre: Finance
Published (Last): 14 May 2009
Pages: 96
PDF File Size: 17.51 Mb
ePub File Size: 13.17 Mb
ISBN: 705-2-73294-344-9
Downloads: 14797
Price: Free* [*Free Regsitration Required]
Uploader: Tauhn

If restraightened, then the same number of tests are again required. Maximum seam depth of 0.

Niagara Lasalle Steel Products – Stressproof ®, ASTM A, Cold Rolled Steel Round Rod

One class, B, is cold drawn with higher than normal heavy drafts to provide higher strength levels, and four grades provide improved machinability. Materials and Manufacture 6.

Standard asym drawn” finish is smooth, Accurate and dark in color. Link to Active This link will always route to the current Active version of the standard. Within the limits of good manufacturing and inspection practices, the bars shall be free of injurious seams, laps, segregation, or other imperfections that, due to their nature, degree, or extent, will interfere with the use of the material in machining or fabrication of suitable parts.

An optical comparator aastm is made of a311 mold from each new or reground die measuring the internal geometry of the die. A lot shall consist of bars of the same size from the same heat which have been stress relieved in the same stationary furnace charge. The heavy draft stress-relieved Class B came into existence with the release of the specification. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

Restricted Incidental Elements S2.

It covers multiple grades and numerous conditions of stress-relieved cold drawn bars to meet minimum mechanical property requirements.

  LEY 1266 HABEAS DATA COLOMBIA PDF

Click below to make an inquiry.

The values stated in each system are not exact equivalents, therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the speci?

To further improve quality, Niagara LaSalle reduced the standard seam depth tolerance for StressProof from 0. The bars are furnished in two classes, A and B.

A311 Class B Stressproof TG&P

You can rely on Niagara LaSalle for all of your steel bar needs. A uniform material which provides exceptional quality for Production, maintenance or special machine parts. Although it also can be induction hardened, it should be watched for quench cracks. Therefore, a warpage test is always performed on the first bar drawn through either a new or reground die. This was followed by the highest temperature stress relieving treatment possible awtm obtain a combination of properties, including strength, wear resistance, minimum warpage and excellent machinability.

The rating of the inclusion count should also be agreed upon and be based upon examination at a magni?

The result is a steel bar product that meets stringent standards and provides a wide variety of benefits, including:. The degree ashm restriction and the number of elements so restricted are both subject to agreement between the manufacturer and the purchaser.

The results then become an integral part of the quality assurance program. Seams deeper than that stated above are rejected. This specification covers cold-drawn, stress-relieved carbon steel bars subject to mechanical property requirements. Class A are normal-draft cold-drawn and stress-relieved rounds, squares, hexagons, and flats. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

The yield strength shall be determined at 0. This abstract is a brief summary of the referenced standard. Combining values from the two systems may result in nonconformance with axtm specification. If this test indicates stresses are out of specification, the die is not used. Details of these requirements aztm be agreed upon between the manufacturer and the purchaser.

For continuous type of treatment, a lot shall consist of 25 tons [25 Mg] or less of the same size of each heat, treated in the same cycle.

  LUIGI CALECA ARCHITETTURA TECNICA PDF

The stress relieving temperature selection is based on 60 years of experience and thorough documentation. Qstm and Polished with special close tolerances s311 on order. NOTE 2— When turned bars are speci? The values stated in each system are not exact equivalents, therefore, each system must be used independently of the other.

Parts you are now heat treating from W311 23 to Rc Within the text, the Asstm units are shown in brackets. Niagara LaSalle developed this groundbreaking process in and forever changed the economics of part production. Niagara LaSalle is exceptionally responsive to the needs of our customers and puts a high priority on providing uniformity in the machinability of our products in order to improve productivity for you.

Every order is inspected for surface defects with a magnetic or roto bar tester.

A Steel Bar | Capital Steel & Wire

To learn more aa311 StressProof or any of our specialty products, please contact us. Where secondary melting axtm employed, the heat shall be de? Mechanical property testing is always the final operation after all processing is completed. The cast or heat analysis shall conform to the chemical composition requirements specified.

One class, B, is cold drawn with higher than normal heavy drafts to provide higher strength levels, and four grades provide improved machinability.

Historical Version s zstm view previous versions of standard. NOTE 1— A typical ordering description is as follows: Tension test shall be made to conform to the requirements specified. The report shall include the name of the manufacturer, ASTM designation and year date and revision letter, if any, class and grade, heat number, size, and grain size if requested.